Here’s the profile I use for Cura
I have shared it via google drive instead
Here’s the profile I use for Cura
I have shared it via google drive instead
I was asked to produce updated config files for the Anycubic Predator which has been upgraded to a duet 2 board running the latest RC of RRF3.
I have uploaded my files to github and they can be found here. This is for a setup where a smart effector has been fitted. There won’t be too much to change for a stock predator if you wanted to get it to work.
The design files can be found on Thingiverse.
He has also added his own version of the PCB adapter so the Duet Smart Effector PCB carriages can be used.
I know I’ve been fairly quiet on here but I have been working on a few things behind the scenes.
Over the next few days I’m going to write about my super cheap enclosure, printing in ABS, a volcano hot end upgrade kit, how I’m getting on with the wham bam flexible system and SMuFF (I now have all the parts printed).
I also feel I’m almost in a good enough place to do a comparison post of pre mods and post mods (aimed at Ryan).
So watch this space…
In the post I wrote about the latest changes I had made to my predator, I described how I had mounted the magball arms and which adaptors I had used.
Well a few days ago, Nealz Engeland pointed me in the direction of these adaptors on thingiverse. How are these different I hear you ask? Ignoring the first two files on there, the second two files allow you to use the PCB adaptors supplied with the smart effector! This improves the precision of the carriages, reducing calibration deviation even further.
I printed the version without the hole for flying extruder and designed these adaptors. They attach in front of the PCB carriage adaptors and the rubber tubing used on the flying extruder attaches to them.
I printed them in ABS, but more on that later…
I’ve created a map for people to add their approximate location. That way if anyone lives nearby and you want to meet up, help each other out, you’ll know if there’s someone close.
Ok, ZeeMaps tops out at 100 views for free maps. So this stopped working pretty quickly. Please use google maps instead
I have been lucky enough to be selected as a beta tester for the flex system for the Predator. I’ve ordered it today so should get it in about a week or so. A review will follow after that.
Their website is here
Since I last wrote a blog post, I have carried out several changes to my current setup. The aim of this post is to try and consolidate all of the changes I have made to try and put a stick in the ground for the readers.
The controller board has been changed to a duet 2 Ethernet. This has been detailed here and here. As well as this, I have changed the effector to a smart effector. This change also meant changing the hot end from the standard v5 clone to an authentic E3D v6. These changes were detailed here.
My setup summarised above was using the original arms that came with the machine. If you follow the Facebook group for the predator, or any other social media channels, you may have heard about the issue of the rapidly wearing rod/arm connectors. This is where the ball in the middle of the connector becomes loose and introduces play into the system. I was suffering from this issue, and it meant that the calibration deviation on my machine was getting worse and worse. One fix for this issue suggested by the community is to replace the rod connectors with ones made by IGUS. These would be great for a normal unmodified machine, but as we’ve already fitted a smart effector, these aren’t really the way to go. It would also be very difficult to make sure that the rods are the same length. This is critical to ensure that the printed parts are accurate, especially as resolution decreases the larger the part.
I ordered a set of arms from Haydn Huntley. He has been known for supplying high quality, high precision arms to the delta community for several years now. I decided to stick to a length of 440mm for the arms, although it has been suggested that arms as short as 405mm will still work. The reduction in length to 405mm will counter the loss in height when fitting a smart effector (which is around 30mm due to the different position of the hot end). I’m not going to tell you which length to order as I have not read anywhere of anyone ordering 405mm and getting them to work over the whole print area. If you feel you will need that extra z height, maybe go for 415 or 420mm. If you are planning to use any sort of multi material changer at some point in the future and will be planning to purge the material outside of the build platform, then I would stick to 440mm arms. The order came within about 2 weeks or so. Just keep in mind that when getting them delivered to the UK that you would be paying somewhere in the region of £30 import duty. They come well packaged, in a cardboard tube and have the length of each arm written on a label. All the ones I received were 440.38mm.
To enable the arms to be mounted to the carriages of the predator, some custom mounts are required. It would be great if the adaptors included with the smart effector fit, but unfortunately, they don’t. I used the adaptors designed by Nealz Engeland but I found that some modification was required to get the holes to line up with the carriage. Don’t forget to swap the little ‘flag’ over required to activate the optical end stops.
I carried out this change while also carrying out some maintenance on my machine. One of the good design factors of the predator is the ability to remove an upright from the machine without much hassle. The predator even stays in place without requiring any other support. I removed each upright in turn and stripped it down to parts. This way, I was able to check that all the rollers of the carriage were correctly in contact with the extrusions and that no play was present. Fortunately for me, there was no play present, but I have read on Facebook, about a number of other predator owners that have had to adjust their rollers to make sure they are all in contact. I also swapped the original 1.8 degree motors with 0.9 degree motors and re-tensioned the belts, but more on that later.
As mentioned earlier, I have previously upgraded the effector from the original to a smart effector. I had modelled up a mount to allow use of the original arms and to mount three radial fans for cooling. The design can be found here.
I have since updated this design to allow the fans to be mounted to the smart effector while using magball arms instead. The design can be found here.
When mounting the arms to the printer, make sure you alternate the polarisation of the magnets. With mine, Haydn fixed the labels on each on at the same polarisation, which made it easier to alternate the arms. Basically, mount one arm label in to the effector, then one arm label to the carriage and then alternate. This helps reduce magnetic interference of the fans etc. Also make sure that you apply lubricant to each of the ball cups. I used bike chain lubricant as per Haydn’s advice.
The motors are very easy to change from one type to another. I had a bunch of motors left over from then I had to send a 3D printer to 3D printer heaven. The main thing to check is that the toothed gear is fitted with the same offset as the gear at the bottom of the printer. Wiring is the same as a 1.8 degree motor. If you’re lucky, you’ll get 0.9 degree motors with removeable cables, in which case, you just plug the old cable into the new motor. Don’t forget that the steps per mm need to be changed from 80 (for 1/16 microstepping) to 160. I’m still assessing whether changing the motors has been a good change or not.
Only a small note to say I’ve added a PanelDue 7 inch. I have mounted it to the top of the frame as shown below.
Along with the above hardware changes, I have been trying to tweak my duet config to improve my settings. I have uploaded my current config to a separate branch on my github for your use. You will notice that the acceleration and jerk are quite high. Below are a couple of pictures of an example part. Ignore the bottom of the part, I am currently working to improve the quality. I will endeavour to keep github up to date.
I have moved a couple of items out of config and into my start gcode. I now do the following.
G32 ;This carries out a delta calibration at the start of the print
G29 S2 ;This reloads the mesh height map which is cleared when carrying out the delta calibration.
That pretty much brings you up to speed.
Before buying the Anycubic ‘D’ Predator, I purchased an Anycubic Linear Plus. I’d been after a delta type printer for a while, after becoming fasinated with the way they work. After all these years, I still find 3D printers mesmerising as they lay down plastic.
As a printer, I’ve generally been happy with how it performs, but I’ve found its bed size a little bit limiting. Its also limited in its processing power, as its fitted with a trigorilla 8-bit board which is being pushed to its maximum capability by the delta geometry.
The design of the Linear Plus is that all of the electronics sit under the bed. This can lead to the electronics being submitted to more heat than would be preferable. It also has a very long bowden tube ~700mm long which requires long retractions of at least 5 or 6mm to eliminate stringing and if you want to move into more flexible materials, its definitely too long.
Before carrying out the conversion, a number of items require printing. If you don’t have another 3D printer, these will need to be made before you start stripping the printer down. They are as follows
You’ll also need some extra parts.
First thing I wanted to be able to achieve was to flip the frame so the electronics were at the top. This would give me easy access to the controller if I wanted to make adjustments to wiring etc without having to remove the bed. This would mean that in theory, I would never have to remove the bed again, reducing any requirements to probe the bed for calibration or meshing.
I’m not going to go too in depth into what I did to achieve this conversion as most of it is self explanatory. What I will do, is provide a brief overview of each step I carried out, in chronological order.
This leaves you with a frame and some electronics. As I was changing the controller board, I also stripped out the controller and screen. This left me with a frame with some motors attached.
I’d previously printed some feet for the Linear Plus, so the first thing I did was swap these over to the other end of the printer. I then turned the printer so it was now the way up I wanted. I then installed things in the following order.
That’s the frame assembled.
Basically, follow the online wiki and my post on installing a duet to the predator. For the endstops, the wires should be connected to the 2 outer pins of the 3 pin connectors. I will post my config on github shortly. Its also worth noting that I am running the duet etc off a 24v PSU that i had lying around. 24v is recommended for the TMC stepper drivers although its not critical.
For the heated bed, I’m using the original power supply connected to a mosfet to control it. I ran cables for the mosfet and the thermistor down the inside of the 2020 extrusion. I will be printing a mount for the mosfet at some point but at the moment its not important.
Please find some photos below of the finished installation.
So its been a while since I’ve updated you on the status of my predator. Since changing over to a duet, I have a number of further changes to my machine.
The upgrade I’m going to concentrate on in this post is the installation of a duet smart effector. With changing this part I am also forced to upgrade to an E3D V6 all metal hot end, which for me is better, as the one supplied by anycubic is limited to a maximum temperature of 260 degrees Celsius.
So what does changing to a smart effector gain you? I would say there are three main advantages.
To be able to use the smart effector with our machine, a number of extra parts are required if you aren’t going to be changing the arms straight away. I’ve modelled all of the parts required and made them available on thingiverse.
You’ll need to print
Make sure you’ve assembled the smart effector as instructed on the wiki.
Start off by running a tap down the 6 mounting holes in the converter for the smart effector. Then mount the smart effector to the converter and secure in place using 6 of the M3 x 20 screws. They do thick out the underside of the converter a fair bit, but that is because we will use them later to mount the fan brackets. Now mount the converter to the 6 arms using the other 6 M3 x 20 screws and the 6 x M3 nuts. You can do this either with the arms attached to the machine or with them removed. Make sure the screws are done up nice and tight so they don’t come loose. Then tap the 2 inner holes on each fan bracket using an M3 tap. Mount the fan duct to the to the fan bracket using the M3 x 6 screws, followed by the radial fan to the bracket using M4 x 30 screws. Repeat for the other 2 assemblies. Finally, mount the fans in the correct position under on the smart effector. Each fan should be wired in parallel and plugged into the part cooling fan port on the smart effector. See below for photos of it installed
For the wiring on the predator to the smart effector, I actually ripped out what was originally there and installed a new harness. This is due to requiring extra cables etc. Just follow the guide on the wiki and you’ll be fine.
Also remember to make the changes to the firmware for the probe and to retune the hotend using M303.