Duet 3 Mainboard 6HC

My early christmas present has come in the form of a shiney new Duet 3 board. Those of you who have read my earlier posts know that I have used Duet 2 ethernet boards (although they were clones) on both the Anycubic Linear Plus and the Anycubic Predator. They are a fantastic board for the money so it made sense to look towards the duet family for my new corexy.

But why did I choose the duet 3 over the duet 2? Well there are a number of reasons why I have done so.

  • The duet 2 tops out at 10 drivers (duet 2 + duex5). If I populate my corexy with all tools, I would need 12 drivers. The duet 3 should be able to handle at least 24 drivers, so expansion isn’t an issue.
  • The duet 3 can be configured to use a raspberry pi (or other similar SBC) to serve the web control, store the gcode files etc and allow the use of plugins with the reprapfirmware. I have been using raspberry pi’s for a number of years with the smart home system so I have a number of them around.
  • As my bed is 500x500x500, I felt that using 3 nema 17’s to move it would be getting towards the top of its limits. I know that its possible to find nema 23’s that would be suitable for use with the duet 2, I didn’t want to restrict myself. The duet 2 can handle up to 2.4 amps per driver and the duet 3 can handle 4 amps.
  • There are individual tool boards planned that would be mounted to the extruder. This reduces the number of wires to each tool from ~12 to 6 (4 for the canbus and 2 for power).
  • The processor has been increased from 120MHz to 300MHz.
  • Any HDMI screen can be connected to the SBC to run the web interface. You are therefore no longer restricted to the paneldue interface.

Now I’m not saying to go out and upgrade a duet 2 to a duet 3 as for standard 3D printers, the cost can’t be justified. But if you are building a tool changer or a larger CNC machine, the duet 3 is a no brainer.

If you do order a duet 3, the following things are supplied:

  • All connectors and crimps to use every connector on the board.
  • A 26 pin cable to connect the duet 3 to an SBC.
  • The crimps required to connect the power cables.
  • An SD card for use in a raspberry pi. (I haven’t used this as my raspberry pi 4 was already setup with an SSD).
  • A sticker for your machine to show that its using a duet 3.

So far, I have the duet 3 setup with a raspberry pi 4Gb. I have updated it and that’s about as far as I’ve got. I have a couple of motors that I’m going to use for the X and Y. I also have the motor that I’m going to use for the tool changer. I have ordered the Z motors (3 off) as well. I’m still on with building my machine so it will be a while before I actually start doing any electronics wiring. Eagle eyed readers will spot that all those motors above equal 6 and there are only 6 drivers on the duet 3 mainboard. I have preordered an expansion board to give me 3 extruders.

More updates on how the build is going to follow.

4 comments

  1. I have the parts for a similar build to yours. A 50x50x50cm corexy using duet 3 and pi 4 with a 10.1″ touch screen. I am hoping to be able to make a machine that can incorporate some basic CAD functionality built in. An all in one, plug and play unit that can utilize nylon and PC. I am only going to use one extruder for now but plan on two once things prove to work well. Mechanical is all done and now into the electrical and electronics.

    1. The raspberry pi 4 can do slicing but I think you will be pushing it with doing CAD work as well.
      I may be wrong but my plans are to continue using solidworks wehn needed

  2. Hey jay
    I’m still interested about your wiring. I have planned a similar setup.
    Today my duet3 + expansion arrived, but I’m not the best electronics.
    Would be nice to see something of your work.
    KR
    Richard G.

Leave a Reply to Richard GrunaCancel reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.